Clogged Plumbing Stack Diagnosis And Remedies

Dealing with a clogged plumbing stack can be difficult and confusing if you’re a homeowner. So it’s good idea to learn a little bit about your home drain line system first. A plumbing installation is comprised of numerous different components designed to work together. This ensures that your house leaves no trace of household wastewater or odor for many decades. Plumbing is similar to a big tree, with a lot of protruding branches connected to a trunk. In this case, the branches are smaller pipes that reach out to water fixtures inside your home. These include your kitchen sink, dishwasher, bathtub, bathroom, shower, and so on. These branches typically connect to a vertical drain line called a stack.

clogged plumbing stack

A clogged stack affects other plumbing fixtures

The stack is considered a is main drain line, which collects and distributes wastewater from all those smaller pipes to the main house drain. It then travels to the house sewer, the city sewer line, then to the public sewer treatment facility. In some areas private septic systems are still in use. Obviously an important part of this elaborate pipe network is the plumbing stack. Also often referred to as vent pipe, this part usually protrudes outward through the roof.

What is Plumbing Stack for a home drain system?

home drain system

Typical home plumbing stack design

All parts of the plumbing installation which handle wastewater are often called a Drain-Waste-Vent (DWV) system. As the name suggests, the system is made up of three main components:

  • Drain pipes, which collect wastewater directly from water fixtures. These fixtures can include your toilet, kitchen sink (secondary drain line), shower, or bath tub.
  • A waste pipe is the main drain line. The main house drain is where wastewater from all drain pipes meet, and then flow to the treatment facility (primary drain line).
  •  A vent pipe (or plumbing stack) allows for air displacement so the water can flow freely inside the main drain line.

The picture on the right shows a representation of how a simple DWV system is designed. All drain pipes from water fixtures are connected to a long vertical line, then to the main house drain line.

Wastewater flows in a downward direction due to gravity. That is the basic principal of almost all drain systems. This also means that only the bottom part of the vertical line acts as main drain line. The upper portion of the pipe system is the actual plumbing stack.

The basic principal of how a drain stack works

Wastewater needs an air passageway behind it in order to flow freely without gurgling, and this is where a plumbing stack comes in. It allows the air to come in and out of the pipe as necessary. When wastewater flows down the drain line, it sucks in a good volume of air to avoid creating a vacuum. In times when the drain pipes are dry, the vent is the escape hatch for odors and all toxic gaseous materials to escape. That is why vents are above your roof line, and above your point of detection.

In many older homes, plumbing stacks are typically made of cast iron. It is a good strong material, but it will start to deteriorate in about 80 years or so. Some older drain pipes can be made of galvanized steel, which unfortunately is subject to rust, corrosion, and getting brittle with age.

Plumbing materials change over time

The use of cast iron and galvanized steel was soon replaced with rust-resistant materials such as ABS plastic. Since the 1970s a newer material, called PVC, took over almost all newer plumbing installation. Copper pipes are still used, but only in rare cases. Local building codes do change over the years. Therefore, it is not uncommon to see plumbing installations in many homes that use a combination of materials.

A Clogged Plumbing Stack

Your plumbing stack is connected to all branches of your drain pipes, including both primary and secondary drain lines. Therefore dealing with clogging issues in this part of the installation is most likely difficult. One of the main reasons is that the symptoms are almost identical to a minor clog. As examples, slow drainage and gurgling sounds when you flush down the wastewater, can actually be a clogged plumbing stack. At this point, the first thing that comes to mind is a partial blockage in a secondary drain pipe; but that may not be the case at all.

When you cannot find any obstruction, the next thing to check is your primary drain line. If you cannot find anything, you may choose to disassemble the p-trap to which the fixture is connected. But, perhaps again, to no avail. All those procedures, in that particular order, are indeed necessary based upon the noticeable symptoms. When finally you realize the problem is more complicated than you expected, then it is time to call a professional drain cleaning service.

After checking all possible issues without results, a professional drain service should be aware of the fact that the vent or plumbing stack can be the source of the problem. One thing that makes the repair quite difficult is that the plumber may need to locate the drain clean-out on the stack. In some cases the clean-out ma have been mistakenly walled over or covered. Someone with an understanding of plumbing design is best suited to locate a clean-out.

Serious Blockage

In the event of a totally clogged plumbing stack, there will be no more gurgling sounds. As a matter of fact, the vacuum in the vent can be very strong that it sucks water out of the entire p-trap connecting to it. If water from a p-trap is moved to the plumbing stack; it also means there is nothing to prevent odor toxic sewer gasses from entering the living space of your house.

A Clean-Out Gives Access To Your Plumbing Stack

Referring back to the image above, a primary drain line has a clean-out plug to access the inside surface of the pipe. It also allows for easy access to the vent from below the soil. The plug is a Y or T shaped fitting designed to give quick access to a primary drain pipe. This allows you to clean out serious obstructions in your plumbing system. However, the culprit of a clogged plumbing stack itself is not always accessible from the clean-out. In extreme cases access from the roof is necessary, and this is a job best left to professional.

Depending on the issue, the plumber can either clean the obstruction from the clean-out access, or from the roof. In any case, it takes a knowledgeable and experienced plumber equipped with modern plumbing tools to get the job done. Some of the most common tools used for a clogged plumbing stack include a commercial-grade electric snake auger, and a hydro sewer jet.

Balkan Can Expertly Clear A Clogged Plumbing Stack

The Balkan family of companies has been in the NYC plumbing industry for more than 65 years. Balkan’s reputation is based upon employing only professionally-trained plumbers, who are equipped with top-of-the-line plumbing equipment. The company meets and even exceeds the requirements to clean and handle both residential and commercial plumbing installations. Naturally, this includes a clogged plumbing stack. This is an area where typical DIY-repair-people, and an inexperienced plumber, should avoid due to the difficulty and risk involved with the job. It requires a good understanding of the plumbing installation to prevent recurrent issues and strict safety measures to avoid job-site accidents. If you need it doen right the first time, contact the Balkan Drain Team.